1.44 MULTI I/O CARD USER GUIDE
     
     INTRODUCTION
     
          1.44 MULTI I/O Card can be used by all personal computer which are in 
     compatible with 16 BIT personal computer or PC/XT. It provides your system 
     5 majors function:
     
     1. FLOPPY DISK ADAPTER: two DS/DD/HD/2HD floppy disk can be drive.
     
     2. PARALLEL PRINTER INTERFACE: The parallel printer interface is designed 
     connect printer.  Parallel printer supports the graphics function by 
     driver software.  User device jumper to enable printer.
     
     3. SERIAL RS-232 CONNECTOR:  There are two serial port, normal the card
     provide you all component for RS-232-1, but RS-232-2 is optional.  You 
     can't define RS-232-1 and RS-232-2 to same device.
     
     4. BATTERY BACK-UP CLOCK/CALENDER:
      -INTERRUPTIVE LEVEL SELECTIVE AREA.
     
     5. GAME PORT: Allows joy-stick connect there.
     
          HOW TO INSTALL THE CARD
     
     - Turn your system ON
     
     - Use flat screwdrive to loose the screw which is used to hold the card in 
     place turn the screw COW.
     
     - Notice there are 31 golden finger which allow you to connect the 
     mainboard to the card. When you install your 1.44 MULTI I/O card, make 
     sure if golden fingers are in contact with the corresponding connector 
     properly.
     
          HOW TO PLUG THE CARD
     
     Consider the following figure of the card.
     
     - Use the flat screwdrive to fix the card. Turn the screw CW.
     
     The screw that mount the card.
     
          Fig 3:- The screw that mount the card.
     
     
     
     
          HOW TO USE THE CARD
     
     1. Floopy Disk
     - Install the drive type:
          When the screen display "PRESS  TO INSTALL DRIVE TYPE" then 
     press  key.  The screen will display menu, you must select 1-3 to 
     install drive type.
     
          Use flag disk cable please check pin 1 make correct to connect disk 
     port golden pin.  Cable other hand have two 34 pin female disk connector 
     distance cable longer connector DRIVER A.
     
     ....
     PC TIMER 1.3 GUIDE:
     
     INTRODUCTION
     
          Consider the hardware configuration of multifunction card, you can 
     see a battery powered clock.  You may ask what is its function and how to 
     use it ?
          
          THE FUNCTION TO TIMER.COM PROGRAM
     
     - Allows you to initialize the date and time in the clock device.  A 
     battery provides power to the clock still works and the date and time set 
     are still maintained.
     
          GETTING START
     
     A> COPY CON: AUTOEXEC.BAT
        TIMER /S Z
     
     In the above commands, the first command line tell DOS to copy information 
     entered on the key-board into the AUTOEXEC.  The second command line enter 
     the TIMER /S program .  The third line means that you can press Crtl Z 
     together or you can only press the F6 key.  This causes the system that 
     key-board input is not into the file and causes information to be written 
     to the file.
     
     TIMER /I:  Initials the clock on the BABY card.  It will first display the 
     time currently exist and ask you enter new time.  If time is correct, 
     TIMER will set it onto the clock device, otherwise an error message is 
     displayed and you have to try again.
     
     NOTE: The TIMER program adopts only 8 characters.
           2 digits for each item.
           2 characters to seperate the digits, you can use any characters. But 
     the standard form is use"
     
     NOTE: Don't use alphabet.